Diagram for Reference

5 to 15V supply - LED indicator Adjustable time detection

A circuit capable of detecting even a very short power outage, can be useful, mainly if embedded into existing appliances like mains powered counters, timers, clocks and the like.

At switch-on of the appliance, the LED illuminates, but pressing on P1 it goes off and remains in this state until a power outage occurs. When power supply is restored, the LED illuminates steadily until you press P1 again.

The circuit sensitivity can be adjusted by Trimmer R5. This means that, under the control of R5, the LED may not light if the mains is missing for a short interval in the 1 to 15 seconds range.

Circuit Diagram :

 Power Outage Warning Circuit Diagram

Circuit Operation :

IC1A and IC1B NAND gates are wired as a set-reset flip-flop. R1 and C1 provide auto-set of the flip-flop when the circuit is powered, so pin 3 of IC1A goes high and pin 4 of IC1B goes low. This allows the outputs of IC1C and IC1D, wired in parallel as inverters, to go high driving the LED D1 on. The flip-flop is reset by pushing on P1.

As the circuit is intended to be powered from the same appliance that is monitoring, the supply is derived from the ac voltage available at the existing transformer secondary winding (see the upper box of the circuit diagram enclosed in the dashed blue line). The circuit will work with ac voltage values in the 5 - 15V range.

A simple diode-capacitor cell (D2-C2) is sufficient to provide the necessary dc voltage. A rather low value was chosen for C2 in order to allow the circuit to detect very short periods of power failure.

The resistance value of R4 + R5 controls the discharge time of C2: with R5 set to the minimum value, the circuit will signal power outages from 1 sec. onwards. If R5 is set to the maximum, the circuit will signal power outages from about 15 sec. onwards.

Notes :

• R3 value should be reduced accordingly if the transformers secondary ac voltage is below 10V
• The circuit can be constructed as an independent unit by simply adding a small transformer with a primary winding suited to the local mains voltage and a secondary winding rated from 5 to 15V AC.

Source :www.redcircuits.com

This circuit of multimedia speakers for PCs has single-chip-based design, low-voltage power supply, compatibility with USB power, easy heat-sinking, low cost, high flexibility and wide temperature tolerance. At the heart of the circuit is IC TDA2822M. This IC is, in fact, mono-lithic type in 8-lead mini DIP package. It is intended for use as a dual audio power amplifier in battery-powered sound players. Specifications of TDA2822M are low quiescent current, low crossover distortion, supply voltage down to 1.8 volts and minimum output power of around 450 mW/channel with 4-ohm loudspeaker at 5V DC supply input.

An ideal power amplifier can be simply defined as a circuit that can deliver audio power into external loads without generating significant signal distortion and without consuming excessive quiescent current. This circuit is powered by 5V DC supply available from the USB port of the PC. When power switch S1 is flipped to ‘on’ position, 5V power supply is extended to the circuit and power-indicator red LED1 lights up instantly. Resistor R1 is a current surge limiter and capacitors C1 and C4 act as buffers. Working of the circuit is simple. Audio signals from the PC audio socket/headphone socket are fed to the amplifier circuit through components R2 and C2 (left channel), and R3 and C3 (right channel).

Circuit diagram:

USB Powered Audio Power Amplifier Circuit Diagram

Potmeter VR1 works as the volume controller for left (L) channel and potmeter VR2 works for right (R) channel. Pin 7 of TDA2822M receives the left-channel sound signals and pin 6 receives the right-channel signals through VR1 and VR2, respectively. Ampl i f ied signals for driving the left and right loudspeakers are available at pins 1 and 3 of IC1, respectively. Components R5 and C8, and R6 and C10 form the traditional zobel network. Assemble the circuit on a medium-size, general-purpose PCB and enclose in a suitable cabinet. It is advisable to use a socket for IC TDA2822M. The external connections should be made using suitably screened wires for better result.

Author: T.K. Hareendran - Copyright: EFY Mag